As camshaft rotates, the lobe, or high spot of the cam, pushes of the valve.
當凸輪軸旋轉時, 凸輪凸起的或者高點的位置, 推動氣門座.
期刊摘選
Angular velocity grinding and linear velocity grinding are the main grinding method for camshaft.
工件恒角速度磨削和工件恒線速度磨削是目前精加工凸輪軸的主要磨削加工工藝.
期刊摘選
In this paper, the theory of cam profiling by CNC swing type camshaft grinder is analyzed.
詳細分析了搖架式凸輪軸磨床凸輪輪廓的數控成形原理.
期刊摘選
These engines are known as dual overhead camshaft ( DOHC ) engines.
這些發動機被稱為雙頂置凸輪軸 ( DOHC ) 發動機.
期刊摘選
The ratio of the crankshaft to the revolutions of the camshaft is 2∶1.
曲軸的轉速與凸輪軸的轉速之比是2∶1.
期刊摘選
The metal shaft, called the camshaft, typically has individual cams for each valve in the engine.
那金屬軸叫凸輪軸, 在發動機里的每個氣門一般有各自的凸輪.
期刊摘選
Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.
拆去凸輪軸固定螺栓,并拆去作為一個總成的鏈輪和鏈條.
期刊摘選
A camshaft driven by a chain or belt turns in the same direction as the crankshaft.
凸輪軸被鏈或者帶驅動,使其朝著曲軸相同的方向轉動.
期刊摘選
The camshaft has a cam, on which there is a lob , or bump.
凸輪軸上有一個凸輪, 凸輪上有一個凸角.
期刊摘選
A formula of the camshaft rotating velocity is deduced while keeping constant metal removal rate.
推導出了保持磨除率基本恒定時,數控凸輪軸磨床磨削凸輪時凸輪軸轉速變化的計算公式.
期刊摘選
The opening of each valve is controlled by a camshaft.
每個閥門的開啟由凸輪軸控制.
期刊摘選
The manganate phosphating technology of camshaft is introduced.
介紹凸輪軸的磷化工藝.
期刊摘選
This is called an overhead camshaft arrangement.
這被叫為頂置凸輪軸裝置.
期刊摘選
Since 1958, an engine with a single overhead camshaft has been used.
從1958年起, 便已使用帶有單頂置凸輪機的發動機.
辭典例句
The influence of inoculant addition amount on the structure and properties of camshaft was investigated.
試驗了孕育劑量對凸輪軸組織和性能的影響.
期刊摘選
The camshaft and crankshaft gears can be connected directly, or meshed.
凸輪軸和曲軸齒輪可能被直接連結, 或者相嚙合.
期刊摘選
Upward camshaft; chain transmission; timing gas distribution system is stable and has little noise.
頂置凸輪, 鏈條傳動, 正時配氣系統傳動平穩,噪音小.
期刊摘選
The front timing cover and and a finished camshaft with timing gear on the end.
前面的時間和范圍,并完成與凸輪軸齒輪的時間就結束.
期刊摘選
This means that the crankshaft will make two revolutions for every revolution of the camshaft.
這意味著凸輪軸每旋轉一次曲軸將旋轉兩次.
期刊摘選
Two TDC ( Top Dead Center ) sensors are mounted at the rear of the single camshaft.
兩個上死點的傳感器安裝在凸輪軸的后面.
期刊摘選
The isothermal quenching process of the ductile iron camshaft was analyzed.
對球鐵凸輪軸的等溫淬火工藝進行了分析.
期刊摘選
The camshaft rotates in phase with the crankshaft, but at half its speed.
凸輪軸和曲軸協調旋轉, 但速度僅是曲軸的一半.
《簡明英漢詞典》
Argon arc remelting hardening is a new technology of manufacturing camshaft.
氬弧重熔硬化是生產凸輪軸新工藝.
期刊摘選