The assembling errors for the stabilization mechanism can significantly influence the performance of sight-line stabilization.
穩定機構的裝配誤差是造成視軸偏差的重要誤差源。
The assembling error of three-axis turntable is unavoidable during assembling process,which is one of the primary system error sources.
作為造成三軸轉臺最終誤差主要的系統誤差源,裝配誤差在裝配過程中難以避免。
On the error distribution and its analysis in the physical experimental design;
物理實驗設計中的誤差分配和誤差分析
Based on the error distribution requirement in the measurement for attached conducting wire in engineering survey the calculating procedure for the measurement of attached conducting wire is deduced from different observing angle and two useful formulas that can be directly applied to the calculation are obtained.
根據工程測量中附合導線測量的誤差分配需要,依照觀測角的不同,推導附合導線測量的計算過程,并推導出兩個實用計算公式。
An effective LUCCD method to decrease the effect of registration error;
一種有效的減弱配準誤差影響的LUCCD方法
When using rectangles as the target,it s difficult to measure the Modulation Transfer Function(MTF) of the space camera accurately because of the registration error between the image of the target and the pixel of the CCD at the initial sampling.
在采用矩形靶標測量航天相機系統MTF時,由于采樣初始時刻靶標像與CCD像元間存在配準誤差,因此給準確測量系統MTF帶來很大困難。
Methods After analysis of elements of the matching algorithm, the different registration algorithm performance are evaluated by the use of a comprehensive registration error based on C ++ to be realized, which can compare with the evaluation results of traditional target registration error.
方法:分析各配準要素的算法原理后,基于C++加以實現,提出使用綜合配準誤差來評價不同配準算法的性能,并與傳統目標配準誤差的評價結果作對比。
Errors of Electrode Area and Electrode Assemble in Small ESG
小型靜電陀螺儀電極面積及電極裝配誤差研究
Analysis of the Characteristics of a Cosine Gear Drive with Assembly Errors Considered
計及裝配誤差的余弦齒輪傳動嚙合特性分析
Effects of accuracy on assembling errors of current transformers based on the Rogowski coils
裝配誤差對Rogowski線圈電流互感器準確度的影響
Assembly Error Stack-up Analysis and Optimum Tolerancing for Aircraft Assembly;
飛機部件裝配誤差累積分析與容差優化方法研究
Parameterized Design and Tooth Contact Analysis with Assembly Errors of TI Worm Drive;
TI蝸桿傳動的參數化設計及存在裝配誤差時齒面接觸分析
Analysis of Shape and Position Error in the Process of AssemblagePrecision Design;
裝配精度設計中的形位誤差問題分析
alignment error
安裝誤差;調準誤差;定線誤差;校正誤差;校直誤差
Impact of Assembly Deflection Error on Contact Characteristics of Orthogonal Face Gear Drive
裝配偏置誤差對正交面齒輪傳動接觸特性的影響
Optimal assembly tolerance allocation based on particle swarm optimization algorithm
基于粒子群算法的裝配公差優化分配
An Algorithm for Improving Error Registration of Netted-Radar System Based on ANN;
利用ANN改進組網雷達誤差配準的算法
Research on the Error Matching Situation of Heterogeneous Master-Slave Surgical Robot
主從異構手術機器人誤差匹配性研究
Error factors affecting analysis of the meshlees weighted least squate method
配點型無網格法的誤差影響因素分析
Error Calibration for Redundancy Collocation of Six MEMS-IMU
六余度配置MEMS-IMU誤差標定
Error Analysis and Accuracy Improvement of Auto-Packing Scale;
自動包裝秤的誤差分析及其精度提高
Error Analysis of Harmonic Effect on Electric Energy Measurement
諧波對電能計量裝置影響的誤差分析
Impact of Slanting Installation Error of PSD on Spot Position
PSD安裝傾斜誤差對光斑定位的影響
Aligning Error Correction Method for Measurement Equipment
測量設備站點安裝對中誤差修正方法
An error ocurred. Retry the profile installation.
出現了一個錯誤。請重新安裝配置文件。